ONGA PANTERA POOL PUMP
The Onga Pantera pool pumps have been specifically designed to incorporate features that will provide reliable and efficient pump operation. The new technology wet end design integrates a unique moulded end-shield cover and lip seal protecting the motor from water damage.
APPLICATIONS:
• Swimming pools from 20,000 litres up to 100,000 litres.
• Solar heating circuits.
• Above ground pools.
FEATURES & BENEFITS
• IP55 (TEFC) motor – with IP55 protection from dust and water the PPP pumps are preserved against elements for many years.
• Stainless steel motor shaft.
• Electrical approvals – the PPP series pool pumps have passed all stringent Australian standards AS/ NZS3136:2001 for safety and is approved for installation within the wetted zone of the pool area, approvals V99108, V02301, V02302.
• Self-aligning barrel unions – Onga’s unique 5 degrees self-aligning barrel unions make pipe work connection a breeze.
• Plastic Yoke and Lip-Seal – The wet end design integrates a moulded end-shield cover and lip seal,protecting the motor from water damage.
• Mechanical Seal – A heavy-duty 3/4″ 316 Stainless Steel mechanical seal (on all models) provides extended life and longer intervals between servicing.
OPERATING CONDITIONS
Suitable for pumping clean non-aggressive liquids without solids or fibers in suspension.
3 year limited warranty.
| Fluid | Water |
| Maximum working pressure | 295 kPa |
| Water (Swimming Pool) temp range | 5ºC-35ºC |
| Ambient temperature | 50ºC maximum |
| MOTOR | |
|---|---|
| Type | TEFC 2 pole continuously rotated |
| Nominal speed | 2800 rpm |
| IP rating | IP55 |
| Insulation class | Class F |
| Thermal overload | Inbuilt auto reset |
| Temperature rise | Class B |
| Frequency | 50Hz |
| Voltage | 230º-240º |
| Bearing type | Deep groove ball bearing with double contact lip seal |
| Bearing temperature rating | 150ºC |
| MATERIAL | |
|---|---|
| Component | Material |
| Pump casing | 20% glass filled with ABS |
| Clacker | 20% glass filled with polycarbonate |
| Impeller | 20% glass filled with ABS |
| Baffle | 20% glass filled with ABS |
| Drain plug | 20% glass filled with ABS |
| Diffuser | 20% glass filled with ABS |
| Basket | Polypropylene |
| Shaft sleeve | Nylon |
| Motor shaft | 400 series stainless steel |
| End shield | Powder coated cast iron |
| Hair and lint pot O-ring | Low friction nitrile |
| Cord/Plug | Nitrile |
| Mechanical seal, 1/2″ type 6 (LTP1100 = type 6 3/4″ | |
| Flexible bellows | Nitrile |
| Stationary face | Ceramic |
| Rotating face | Carbon |
| Spring | 18-8 stainless steel |
| PUMP MODEL | A(mm) | B(mm) | C(mm) | D(mm) | E(mm) | F(mm) |
|---|---|---|---|---|---|---|
| PPP550 | 630 | 487 | 121 | 185 | 288 | 290 |
| PPP750 | 630 | 487 | 121 | 185 | 288 | 290 |
| PPP1100 | 630 | 495 | 144 | 185 | 288 | 290 |
| PPP1500 | 630 | 495 | 144 | 185 | 288 | 290 |
| PPP1500H | 630 | 495 | 144 | 185 | 288 | 314 |
Note: Dimension ‘E’ an additional 160mm clearance height required above the pump to remove strainerbasket for maintenance and cleaning purposes. Unless otherwise specified, all dimensions in mm.Fixing holes accept 8mm fasteners.
